Seawater Service Solution Annealed Super Duplex Round Bar Low Thermal Expansion
Product Details:
| Place of Origin: | Shanxi, China |
| Brand Name: | Taigang |
| Certification: | ISO 9001:2015, EN 10204 3.1 Mill Test Certificate |
| Model Number: | 2507 Super Duplex Bar S32750 |
Payment & Shipping Terms:
| Minimum Order Quantity: | 300 Kilograms |
|---|---|
| Price: | USD 8.5-14.0 / Kilogram |
| Packaging Details: | Plastic film bundle with wooden case |
| Delivery Time: | 12-20 days depending on size |
| Payment Terms: | T/T,L/C at sight |
| Supply Ability: | 800 Tons per Month |
|
Detail Information |
|||
| Port: | Shanghai | Package: | Standard Sea-worthy Packing |
|---|---|---|---|
| Keyword: | Stainless Steel Round Bar | Place Of Origin: | Shanxi, China |
| Grade: | 2507 / UNS S32750 / 1.4410 | Diameter: | 6mm - 300mm |
| Length: | 1000-6000mm Or Cut To Order | Tolerance: | H9 / H11 |
| Finish: | Peeled, Polished, Solution Annealed | Yield Strength: | ≥550 MPa |
| PREN: | ≥40 | Standard: | ASTM A276, ASTM A479, NORSOK On Request |
| Highlight: | 2507 Super Duplex Round Bar,UNS S32750 Forged Bar,High Strength Shaft Blank |
||
Product Description
2507 sits above 2205 in the duplex family. With 25 percent chromium, 4 percent molybdenum, 0.27 percent nitrogen and a pitting resistance equivalent number above 40, it is designed for seawater pumps, subsea hardware and process equipment that must survive chlorides at elevated temperature without cracking. The yield strength of 550 MPa is more than 2.5 times that of 316, so a shaft can be significantly slimmer for the same torque, which reduces bearing loads and seal friction.
Machining super duplex requires care: the material work hardens quickly if the tool rubs instead of cuts, so our bars are supplied in the solution annealed condition with cutting recommendations and, where the application requires, low temperature impact test data. Heat treatment after welding is not needed for this grade, which simplifies fabrication.
- Highest Duplex Strength: A minimum yield strength of 550 MPa and tensile strength of 800 MPa give the highest load capacity in our duplex range, allowing compact shaft and valve designs.
- Seawater Service: A pitting resistance equivalent number above 40 provides resistance to pitting, crevice attack and chloride stress corrosion cracking in seawater and brine up to about 60 degrees Celsius.
- Solution Annealed Structure: Bars are annealed at 1025 to 1125 degrees Celsius and water quenched to guarantee the ferrite and austenite balance that controls toughness and corrosion resistance.
- Low Thermal Expansion: Thermal expansion close to that of carbon steel reduces distortion and residual stress in welded assemblies and simplifies tolerance control on long shafts.
- Impact Toughness: Charpy impact values remain strong at low temperature, which matters for subsea and cold climate equipment operating below zero.
- Machining Guidance: Recommended cutting parameters, insert grades and deep hole drilling advice are provided with every shipment to help shops avoid work hardening.
| Parameter | Specification |
|---|---|
| Grade | 2507 / UNS S32750 / 1.4410 |
| Chemical Composition | Cr 24–26, Ni 6–8, Mo 3–5, N 0.24–0.32, C ≤ 0.03 |
| Tensile Strength | ≥ 800 MPa |
| Yield Strength | ≥ 550 MPa |
| Elongation | ≥ 15 percent |
| Hardness | ≤ 310 HB |
| PREN | ≥ 40 |
| Diameter Range | 6 mm to 300 mm |
| Standard | ASTM A276, ASTM A479 |
| Packing | Plastic film bundle, wooden case |
Super duplex bar serves seawater pump shafts, impellers and wear rings, subsea valve stems and actuator components, desalination high pressure piping, offshore deck hardware, pulp mill bleach plant equipment and chemical tanker cargo systems. Its combination of strength and chloride resistance also makes it a preferred material for large diameter propeller shafting on workboats and for fasteners used below the waterline.
Where 2205 reaches its temperature or stress limits, 2507 is the next step before nickel alloys become necessary, and our team can review the process data to confirm the transition point.
Bars are protected with plastic film, bundled by diameter, strapped and packed into wooden cases or loaded into containers with timber dunnage. Labels record grade, heat number, diameter, length and bundle weight.
EN 10204 3.1 certificates include chemical analysis, tensile results, hardness and, where requested, Charpy impact values. Positive material identification and third party inspection can be arranged before shipment for project orders that require documented incoming inspection.
Tell us the grade, diameter, length, surface finish and quantity, and we will reply with a technical quotation within one working day. Round bars from 6 mm to 300 mm are cut on our band saws and lathes, bundled by diameter, wrapped in plastic film, and loaded into 20 or 40 foot containers.
Sample lengths of 300 mm are available for material verification before bulk orders are released. Our sales engineers will confirm mill certificates, heat numbers and delivery dates in writing so that your purchasing team has a complete paper trail from inquiry to container loading.



